您的位置: 专家智库 > >

上海交通大学材料科学与工程学院上海镁材料及应用工程技术研究中心

作品数:2 被引量:3H指数:1
相关机构:华东理工大学机械与动力工程学院更多>>
相关领域:一般工业技术更多>>

文献类型

  • 2篇中文期刊文章

领域

  • 2篇一般工业技术

主题

  • 1篇低周
  • 1篇低周疲劳
  • 1篇低周疲劳性能
  • 1篇镁合金
  • 1篇镁基
  • 1篇镁基复合材料
  • 1篇合金
  • 1篇复合材料
  • 1篇NANOCR...
  • 1篇SIC
  • 1篇SIC颗粒
  • 1篇MG-AL
  • 1篇MG_ALL...
  • 1篇复合材
  • 1篇MILLIN...
  • 1篇PEAK
  • 1篇HYDRID...

机构

  • 2篇上海交通大学
  • 1篇华东理工大学

作者

  • 1篇丁文江
  • 1篇王瑶
  • 1篇邹建新
  • 1篇曾小勤
  • 1篇吴晓梅
  • 1篇李德江
  • 1篇朱明亮

传媒

  • 1篇机械工程材料
  • 1篇Transa...

年份

  • 1篇2025
  • 1篇2013
2 条 记 录,以下是 1-2
排序方式:
Microstructure characterization and hydrogen desorption behaviors of Mg-Al-H powders prepared by reactive milling in hydrogen被引量:3
2013年
Microstructure and phase evolutions of Mg-A1 powders ball milled in hydrogen atmosphere were investigated. Both in Mg-3%A1 (mass fraction) and Mg-9%AI systems, fl-MgH2 phase was observed upon a short milling time of 4 h and its maximum content of-80% was reached after 32 h. Neither as-milled powders of the in the two systems contain Mgl7All2. However, heating the milled powders of Mg-9%AI powders to 350 ~C resulted in the precipitation of Mg17A112. DTA/TG analyses of those powders milled for 8-40 h showed that either well-developed peak doublets or shoulders were observed, which plausibly corresponded to the separate hydrogen desorption from different particle fractions offl-MgH2.
王瑶曾小勤邹建新李德江吴晓梅丁文江
关键词:HYDRIDING
半固态注射成型SiC_(p)/AZ37镁合金复合材料的低周疲劳性能
2025年
采用半固态注射成型工艺制备不同质量分数(0,5%,12%)SiC_(p)/AZ37镁合金复合材料,研究了SiC_(p)添加量对显微组织、拉伸性能和低周疲劳性能的影响。结果表明:不同SiC_(p)添加量下复合材料均由初生α-Mg、β-Mg17Al12析出相和SiC_(p)组成,相比AZ37镁合金,晶粒尺寸显著细化,析出相数量减少,屈服强度和弹性模量增大,抗拉强度和断后伸长率减小,随着SiC_(p)添加量增加,拉伸断裂模式由韧性断裂向韧脆混合断裂、脆性断裂转变;随着SiC_(p)添加量增加,循环滞回环变窄,低周疲劳寿命先延长后缩短,循环响应为初始循环软化后循环硬化直至失效,循环硬化程度增大。
周丽萍谷立东曾小勤莫旭阳朱明亮
关键词:镁基复合材料SIC颗粒低周疲劳
共1页<1>
聚类工具0